BROADCOM ADVANCED CONTROL SUITE 2 10.4 DRIVER

Select the license key, click Open , and then click Upgrade License. Here’s most popular questions on this driver. The test writes patterned values to the memory and reads back the results. All adapters in the team are configured to receive packets for the same MAC address. If performing a silent upgrade, your system may reboot automatically. The degree to which Windows performance may suffer depends on system configuration. This item is not available for PCI Express type adapters.

Uploader: Akinogrel
Date Added: 6 January 2004
File Size: 66.28 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 56770
Price: Free* [*Free Regsitration Required]

Such information includes the link status of the adapter and network connectivity. To comtrol a silent install and create a log file at f: On the Statistics tab, you can view traffic statistics for both Broadcom network adapters and network adapters made by others. The list of available properties for your particular adapter may be different. A count of directed data frames that were successfully received. You can specify up to 3 additional probe targets to serve as backups by assigning IP addresses to the other probe targets.

The outbound load balancing scheme is determined by the BASP driver. A count of frames that are successfully transmitted as indicated by the status value Transmit OK to a group destination address other than a broadcast address. Click the name of the newly created team.

Broadcom Advanced Control Suite 2: Broadcom NetXtreme® 57XX User Guide

This is a physical MAC media access control address that is assigned to the adapter by the manufacturer.

  HP ELITEBOOK 8460P DISPLAYPORT DRIVER

In this mode, at least one of the brodacom partners must be in active mode. The benefit of this approach is that it enables load balancing and failover. Normally the TCP segmentation is done by the protocol stack. The bus clock signal frequency used by the adapter.

It is important to take both measurements into consideration, as one result alone is not indicative of the characterization of the cable being tested. To ensure network connectivity to the probe target, ping the probe target from the team.

Ensure there is network connectivity between the team and the probe target on the untagged VLAN. Set the probe interval the number of seconds between each retransmission of a link packet to the probe target and the maximum number of probe retries the number of consecutively missed responses from a probe target before a failover is triggered. If the adapter icon show a superimposed red letter X, the adapter is not connected to the network.

Click Yes to brladcom the current configuration. To disable Ethernet Wirespeed, change the setting to Disable. The team name cannot exceed 39 characters, cannot begin with spaces, and cannot contain any of the following characters: Teaming is done through the Broadcom Advanced Server Program software. Repeat this step for all listed team members, click OKand then click Next.

On the File menu, click Adanced Restore. Assign any available adapter or adapters to the team by moving the adapter from the Available Adapters list to the Load Balance Members l ist. This information is displayed only when there is a team see Configuring Teaming. This property requires the presence of a switch that is able to process Jumbo frames. This locally administered address consists of a digit hexadecimal number. Frames size less than byte with bad FCS.

  AZUREWAVE BLUETOOTH BT 280 DRIVER

Broadcom Advanced Control Suite 2 9.7.0.1 For Windows All

All load balance members have to fail before the standby member takes over. Normally the TCP segmentation is done by the protocol stack.

The link speed of the adapter. This condition would signify that the cable length is too long and not operational.

To continue using , please upgrade your browser.

If you do want to specify more than one, for each additional probe target up to a total of 4click the next probe target in the list, type the target IP address in the IP Address box, and then click OK. Provides detailed performance statistics for the selected team this BASP Statistics tab is displayed only when you click the name of an adapter that is part of a team. Some properties may not be available for all Broadcom network adapters.